Tubular Evaporators

1-Effect, 5013 Sq. Foot, 304 Stainless Steel Evaporator

Stock #VL1169-02

Unused from new Crown Iron Works approximately 5013 square foot (466 square meter) 1st stage evaporator. 304 stainless steel tubes has (1064) 3/4" (19.05 mm) diameter X 24' (7315 mm) long 304 stainless steel tubes rated 15 psi/full vacuum (1.03 bar/full vacuum) design pressure. Has 58" (1473 mm) diameter X 24' (7315 mm) long shell rated +/-1 psi (-0.06/0.06 bar) design pressure. New 2004.

Location: Perry England Warehouse

Add to Cart View Details

833 kg/Hour 3-Effect with ATFD

Stock #RG2109

Used approximately 833 kg/hr (20kld) stainless steel three stage forced circulation evaporator with 500 litre per hour agitated thin film dryer. System is all mounted in a mild steel frame.

Location: Europe

Add to Cart View Details

4200 kg/Hour (9259#/Hour), 1-Effect, Falling Film Evaporator

Stock #RG8550

Used 4200 kg per hour (9259# per hour) Epcon one step falling film 304 stainless steel evaporator. Reportedly made in 1999 and previously used as a pre-evaporator for milk concentration in ice cream factory. Designed for concentrating from 6% up to 20% at 72° Celsius.

Location: EUROPE

Add to Cart View Details

4800 kg/Hour (10582#/Hour), 3-Effect Wiegand Falling Film Evaporator

Stock #VL1269

Used Wiegand 3-effect stainless steel falling film evaporator. Unit designed for approximately 4,800 kg/hour of jelly liquors evaporating capacity. Feed rate approx 5,240 kg/hourr at 50°C. Output rate 440 kg/hr. Steam consumption with full load at constant pressure of 7 aute at the steam header or constantly 5 atue at the thermo-compressor approximately 1,460 kg/hour. Consumption of cooling water when heating from 28 deg.c. to 40°C. approximately 70 cubic meter/hour. Includes pumps, pipework and various instrumentation.

Location: SPAIN

Add to Cart View Details

Anhydro 2 Step Falling Film Evaporator

Stock #ZG62906

Used Anhydro 2-step falling film vacuum evaporator. Water evaporating capacity: 1.000 kg/hour. Built 1990. Previously used in a juice factory.

Location: DENMARK

Add to Cart View Details

45000 #/Hour Titanium Evaporation System

Stock #ZG62860

Evaporation System – Unitech Titanium Falling Film Evaporator Evaporator system rated 45,000 lbs/hour. Unitech titanium falling film evaporator manufactured in 1993 but unused until 2008 then operated for approximately 9 months. Includes Incoloy 825 vapor body; 15,862 square foot heat transfer section with 872 Grade 2 titanium 2" diameter tubes X 36' long; and MVR compressor driven by a 500 HP motor. Design train capacity is 92 gpm, distillate flow 83.95 gpm. This converts to 44,457 lbs/hour water evaporation. Includes manual valves and selected 304 stainless steel and 316 stainless steel piping manifolds, and structural foundation for evap vessel and deaerator. Ladders, grating, and access steel also available for an additional cost. MVR Compressor: MVR vapor compressor by A C Compressor Corporation. 22543 acfm centrifugal air compressor. Single stage with buffered labyrinth type shaft seal. Features a cast iron housing with a stainless steel impeller and shaft. Inlet temperature 223 degrees F. Inlet pressure 15.6 MMH20, discharge pressure 19.52 MMH20. Rated speed 628 RPM. Maximum continuous speed 6289 rpm. Maximum allowable discharge temperature 400 degrees F. Maximum allowable discharge pressure 15.7 psig. Driven by a Siemens, Type CG II 500 HP, 1775 RPM, 4000 volt motor. Motor rated for 60 amps @ 60 Hz. Compressor is coupled to motor through a Westech high speed gear unit with oil cooler, model # 10705. Drive couplings are by Rexnord and system features oil control and vibration analysis with a Bently Nevada 3300 system. Built 1993 – UNUSED. Installed in 2008 – used approximately 9 months, idled since then.

Location: CANADA

Add to Cart View Details

Tubular Evaporators